Mercedes-Benz E-Class W214 — Illuminated Grille Installation Reference

Product and vehicle scope

The source product image identifies this illuminated-grille kit for the 2024–2025 Mercedes-Benz E-Class W214. The archive category says model years from 2024 onward, but it does not establish compatibility beyond the image's stated range or across every grille design, equipment package, market or left-/right-hand-drive configuration. Confirm the actual vehicle and kit revision before installation.

The source image's numbered legend identifies:

1. Upper and lower illuminated light strips.
2. Light-strip mounting brackets.
3. Cable-routing strip/tool.
4. Main wiring harness with a control module.
5. Terminal connector housing.
6. A fuse labelled 3 A.
7. Light-strip connection harness for the hood/engine-compartment side.
8. Light-strip connection harness for the interior side.

The module pictured in the source is labelled for Mercedes-Benz 214 and shows a 12 V input marking. These are observations of the illustrated component, not an instruction to select an arbitrary 12 V supply or fuse position. The exact kit wiring diagram and vehicle circuit information are still required. The present English image mistranslates several legend items and leaves Chinese visible; use the corrected list above when identifying the illustrated parts.

This specific locally bound recording runs approximately 4 minutes 9 seconds. It starts with the grille already removed. It is not a complete bumper/grille removal and refitting procedure. The current English version remains a draft: its subtitle and voice scripts end at about 02:41, although later source pictures still show electrical installation. Chinese instructions in those later pictures have not been replaced by usable English guidance.

Step-by-step video navigation

1. 00:00–00:34 — Distinguish and position the light strips. The source distinguishes the upper strip by its longer notch and the lower strip by its smaller notch, then demonstrates aligning the protruding side and locating tabs on the removed grille. The current English “E24” should read E-Class W214. Follow the demonstrated orientation together with the exact kit instructions; do not assume that either strip can be interchanged.

2. 00:45–01:38 — Fit the retaining brackets. The installer aligns the bracket with the illustrated clip positions, presses it into place and repeats the operation for the other strip. Around 01:20 the source caption describes clipping the bracket into place. The English “Use the computer operation” is a recognition/translation error in this mechanical section; it is not evidence of a coding requirement.

3. 01:39–02:04 — Identify the harness and connect the grille branches. The recording introduces the supplied harness/module, routing aid and connector. It describes four plugs for the grille-light connections and shows the branches being joined near the front of the engine compartment. Four plugs does not mean four pin positions. The source does not give a complete connector-face diagram or protection/fixing specification for the route.

4. 02:05–02:21 — Bring the terminal-ended lead into the cabin. The installer points out the demonstrated engine-compartment route and uses a cable-routing aid to bring the lead with loose terminals into the interior, where it emerges beneath the floor/trim area. Confirm the exact pass-through, sealing, edge protection and clearance before reproducing the route. A close picture of that area does not establish a safe universal opening or permission to pierce a seal.

5. 02:23–02:41 — Join the interior harness connectors. The demonstration shows the supplied connector housing and terminal-ended lead being matched with the interior harness. Its caption/script describes brown-to-brown and pink-to-gray in this arrangement. Those colors are not a universal circuit or polarity specification. Verify terminal positions, locking orientation and the exact harness revision from the wiring information before inserting terminals.

6. 02:42–03:11 — Review the omitted footwell-light branch. The source continues after the English translation stops. It shows a harness branch in the driver footwell, then the footwell lamp being released around 02:54 and connections being handled below the dashboard. This portion must be transcribed and checked manually. The observed lamp action alone does not identify the correct connector terminals, electrical role or full trim procedure.

7. 03:12–03:57 — Review the omitted power/fuse connection. The source moves to the driver-side dash-end electrical carrier and shows the supplied lead, numbered connector positions and fuse work. Captions refer to power, the supplied fuse and numbers on the connector. The available pictures do not supply a verified circuit designation, complete cavity mapping or insertion/locking sequence. Do not choose a fuse slot or terminal solely by the visible color or relative position; obtain the applicable kit schematic and vehicle circuit identification.

8. 03:58–04:09 — Ending and outstanding checks. The final seconds show branding. They do not establish an installed lighting test, vehicle-function check, water-sealing check or successful grille/trim refit. Keep the installation open until those checks and the missing electrical instructions have been verified.

Results and troubleshooting

The archived article's effect-display and troubleshooting sections are empty. It provides no source-backed fault table. Before treating this reference as a complete installation procedure, add the applicable grille/bumper removal and refit instructions, exact harness/module diagram, terminal and fuse/circuit identification, protected sealed cable route and finished-operation evidence.

The finished check should record actual lighting and switching behavior, connector retention, wiring clearance, trim/grille refit and any affected original vehicle functions. Whether programming is required and whether the accessory is permitted for the intended use must be established separately for the exact vehicle, kit and market. This reference supplies no coding values or approval conclusion.

Source reference

The archived CKCP E-Class W214 illuminated-grille article contains this one product image and a specific installation-video link. Saved official-video records connect that article to the local source and current English recording. This review restores readable parts and navigation text from those exact materials. It preserves the existing media links and recorded publication history; it does not certify the draft English video or the electrical installation.